Voltesta

Ride world: where does the battery's energy go?

Ride an electric scooter round a 3D town loop with a flyover. Change speed, load, wind, tyres and regen, and watch power, Wh per km and range change lap by lap.

How this lab works

  1. Ride one lap

    The scooter starts at 30 km/h on a 900 metre loop: town, a flyover, then open road. Watch the power jump on the climb and drop on the way down.

  2. Change one thing

    Change only one setting, such as the speed or the load, and ride another lap. Each finished lap is saved in the table so you can compare.

  3. Read the result

    The bars show where the power is going right now: air, tyres, hill, and losses in the motor and controller. Wh per km tells you the range a full battery would give at that style of riding.

Ride the loop

Drag to look around. Use + and − to zoom.

How to ride
Riding mode
Load and road
Clock speed
0Speed (km/h)
0Battery power (kW)
0Current (A)
0Pack voltage (V)
–Use right now (Wh/km)
–Trip average (Wh/km)
–Range left (km)
0Distance (km)

Where the power is going right now

Pushing air0 W
Tyres on the road0 W
Climbing0 W
Motor, controller, lights0 W
Coming back from braking0 W

Battery power round the loop

This lapLap beforeHeight of the road

Your laps

Finish one lap to see it here. Then change one thing and ride another lap to compare.

LapAverage speedWh per kmFull-battery rangeRecoveredSettings

Things to try

  1. Ride a lap at 30 km/h, then a lap at 60 km/h

    Air drag grows with the square of speed. Wh per km roughly doubles, so the range of the same battery is cut to about half.

  2. Add 100 kg of load at the same speed

    The tyre bar and the hill bar grow, the air bar does not. Weight matters most on climbs and in stop-and-go riding.

  3. Switch to soft tyres

    Rolling resistance rises by more than half. Checking tyre pressure is the cheapest way to get range back.

  4. Hold 30 km/h over the flyover with regen on, then with regen off

    On the way down the sparks turn green and flow back to the battery. The saving is a few percent, and the friction brakes do less work. At 50 km/h the air already holds the scooter back, so there is nothing left to recover.

  5. Set a 20 km/h headwind

    The scooter now pushes air as if it were going 20 km/h faster. Wind is why the same road can give different range on different days.

  6. Use throttle and brake yourself, and pull away at full throttle

    The motor gives full torque from zero speed. Current is highest and the pack voltage sags while you accelerate.

How the simulation works

Four things resist the scooter. Tyres on the road take a force equal to the rolling resistance times the weight. Air takes a force that grows with the square of the speed. A hill takes the weight times the slope. Speeding up takes the mass times the acceleration.

The hub motor gives up to 95 Nm at the wheel from zero speed, and then holds a fixed power for the riding mode: 1.2 kW in Eco, 2.0 kW in Normal, 2.8 kW in Sport. Power at the wheel is force times speed. The battery has to give more than that, because the motor windings heat up with the square of the torque and the controller and lights take their share.

The pack is 16 cells in series and 30 Ah, about 1.78 kWh. Its voltage follows the state of charge and sags under current because of 0.06 ohm of internal resistance. Regen is capped at 1.2 kW, fades out below about 12 km/h, and is blocked when the pack is above 98%, because a full battery has no room.

These are typical figures for a city scooter, chosen so the lesson is clear. Your own vehicle will differ. Use the pattern, not the exact numbers.

Every value here comes from a teaching model running in your browser, with typical figures. They are not measurements from real hardware.