Charge world: why the last 20% takes so long
Plug a scooter into a 3D wall charger and watch its 16 cells fill. Change the charger current, the chemistry, the weather and the cooling, and see the charging time, the heat and the cost change.
How this lab works
Watch one charge
The pack starts at 10% on a 10 amp home charger. The clock runs fast. The current stays flat for most of the charge, then falls away near the top.
Turn the charger up
Press Start again, raise the charger current and watch the cells change colour as they warm. The taper now starts earlier, because the pack reaches its top voltage sooner.
Compare your charges
Every finished charge is listed with its time to 80%, total time, peak temperature, units and cost.
Charge world: why the last 20% takes so long
Voltesta, voltesta.com
Charge the pack
The 3D picture needs WebGL, which is switched off in this browser. The controls, numbers and charts on this page still work.
Drag to look around. Use + and − to zoom.
Current, charge and temperature against time
Current (right-hand scale)Charge (%)Pack temperature (°C)
Reading the picture
- The glass pack is a large copy of the scooter's 16 cells. The level is the state of charge; the colour is the temperature.
- The dots on the cable move faster when more current flows.
- The dashed line on the chart is 80%.
Your charges
Let a charge finish to see it here. Then press Start again, change one thing and compare.
| # | Settings | Time to 80% | Time to finish | Peak temperature | Units used (kWh) | Cost at ₹8 a unit |
|---|
Things to try
Home charger: 10 A, from 10% to full
About 2 hours to 80% and 2 hours 45 minutes to full. The pack warms by only 3 °C. It takes about 1.8 units, roughly ₹15.
Fast charger: 60 A with the fan on
80% in about 25 minutes, then another 20 minutes for the last 20%. The pack reaches 45 °C and makes five times the heat of the home charge.
The same 60 A charge with no fan
The pack hits 45 °C early, the BMS halves the current, and 80% now takes about 40 minutes. A bigger charger does not help a pack that cannot shed its heat.
Set the air to 5 °C, then to −5 °C
At 5 °C the BMS allows only 6 A, whatever the charger can give. Below freezing it does not charge at all, because charging a frozen cell damages it for good.
Switch to LFP cells at 30 A
LFP holds almost the same voltage until it is nearly full, so the taper is short: about 14 minutes for the last 20% against 21 minutes for NMC.
Stop at 80% on the fast charger
You leave after 25 minutes instead of 45 and skip the slowest, hottest part of the charge.
How the simulation works
The charger tries to push the current you set. The pack's voltage is its resting voltage plus the current times its internal resistance. While that stays under the top voltage, 4.2 V per cell for NMC and 3.65 V for LFP, the full current flows. This is the constant-current stage.
Once the pack reaches its top voltage the charger holds that voltage, and the current is whatever still fits: the gap to the resting voltage divided by the resistance. As the cells fill the gap closes and the current tapers. Charging ends when it falls to 1.5 A. A bigger current reaches the top voltage earlier, which is why a fast charge starts to taper near 80% and a slow one near 98%.
Heat in the pack is the current squared times the resistance, so six times the current makes thirty-six times the heating power. The BMS allows only 0.2C below 10 °C and nothing below freezing, halves the limit to 0.5C at 45 °C, and stops at 55 °C. The charger is taken as 90% efficient, and a unit costs ₹8.
The pack is 16 cells in series and 30 Ah with typical figures. Your own vehicle and charger will differ, and a real BMS uses its maker's limits.
Every value here comes from a teaching model running in your browser, with typical figures. They are not measurements from real hardware.